How to Make a Pave Beads Bracelet

Nov 262011

Pave Beads Bracelets are currently enjoying a wellspring of demand. Now wearing a piece of jewelry that is made by ourselves becomes a fashion. To present a handmade jewelry can full express your affection and love to your special ones. It may be very expensive to buy a ready to wear jewelry, but it would never be to make your own one. Just following the steps, you can found how amazing it will be to braid a beautiful and fashion bracelets. Please have fun!

Instructions:
	Tools we need 12 Clear Crystal Beads 1 Rhinestone Beads 2 Black Crystal Beads Braiding Cord Scissors Lighter

Loop Knot
	STEP 1 Begin the bracelet by cutting three pieces of cords with scissors, the length of them were 16inches, 16inches and 30 inches.
	STEP 2 Fold 30 inches cord in half and tie a knot on the centre, form a 1/2 inch loop.
	STEP 3 Through the 16inches cord in the loop. Pull the both sides cords to tighten the knot.

Square Knot
	STEP 1 Place the right cord under the centre thread lengths, then cover the left cord. Allow this section of the cord to be loose.
	STEP 2 Pass the left cord cover the centre thread and over the right cord. Pull the cords to tighten the knot.
	STEP 3 Move the left cord again under the centre, then cover the right cord.
	STEP 4 Pass the right cord cover centre and over the left cord.
	STEP 5 Pull the cords to tighten the knot. So you have formed a square knot.

Adding the beads
	STEP 1 Strand one crystal bead along the centre cord.
	STEP 2 Then make another square knot.
	STEP 3 Repeat step1 to step 2, six crystal beads have been stranded along centre cord. Make one and a half square knot behind the sixth bead, as you see in red loop.
	STEP 4 Strand a rhinestone bead along centre cord. Make one and a half square knot behind the rhinestone bead.
	STEP 5 Repeat step1 to step2, strand the other six crystal beads. Make two square knot behind the last bead.
	STEP 6 Cut off the excess cord on both sides, just left 5mm length long.
	STEP 7 Light up lighter, heat and dissolve the 5mm cord on both sides.
	STEP 8 So that we have finished the beading process.

Closing the Bracelet
	STEP 1 Form the bracelet into a circle, get another 16 inches cord prepared.
	STEP 2 Make a loop knot over the ends of the cord with the 16 inches cord.
	STEP 3 Fit the bracelet onto your wrist and size it so that the bracelet is both comfortable and attractive. Remove your wrist. Mark the correct size for your bracelet, then start to make several square knots according to the length you want.
	STEP 4 So that we have finished the square knots.
	STEP 5 Cut off the excess cord on both sides, just left 5mm length long.
	STEP 6 Light up lighter, heat and dissolve the 5mm cord on both side.
	STEP 7 Strand two black crystal beads and tie a loop knot on the both ends of the cord. Cut away the excess thread length.

–>

247 Responses to “How to Make a Pave Beads Bracelet”

Linwood Heiberg says:

August 27, 2012 at 7:26 am

Great blog! Is your theme custom made or did you download it from somewhere? A design like yours with a few simple tweeks would really make my blog shine. Please let me know where you got your design. Cheers
8Seasons Team says:

August 30, 2012 at 9:44 pm

Hi, Linwood,
Thanks for your visit here. I am proud to say that our blog is established by our team with great efforts, patience…. Sure you like it~~
dre beats headphones says:

August 31, 2012 at 9:41 am

I like the helpful info you provide in your articles. I’ll bookmark your blog and check again here frequently. I am quite sure I’ll learn many new stuff right here! Best of luck for the next!
Eldora Knoy says:

September 22, 2012 at 12:21 pm

The theme of your blog is totally fresh, I am certain that the visitors who come across your blogs will appreciate your content and opinions.
gw2 gold says:

October 18, 2012 at 2:14 am

Definitely, what a fantastic blog and revealing posts, I will bookmark your blog.Best Regards!
democratic says:

April 11, 2013 at 7:16 am

After research a few of the blog posts in your website now, and I really like your manner of blogging. I bookmarked it to my bookmark website listing and shall be checking back soon. Pls take a look at my web page as well and let me know what you think.
webwatcher review says:

April 26, 2013 at 2:26 pm

Enjoyed reading your story. I am going to bookmark your website, so I can come back and read more later. Take care for now. Reg Zooka

247 Responses to “How to Make a Pave Beads Bracelet”

Leave a Reply Cancel reply